Byta abs sensor saab 9-5
Step one: disconnect the battery use 13 mm socket , first negative terminal, then positive Step two: disconnect battery vent tube Step three: loosen battery hold down with a 13 mm wrench, it's behind the battery and hard to get a wrench on.
29.09.2007: Saab 9-5 Front Suspension - photo.platonoff.com
ABS Speed Sensor. 30 Day Return Policy. The magnetic retriever might come in handy here as the nut may fall off if you're not careful. Buy ABS Speed Sensor Here. Save Off Dealer Prices. I apologize. Anybody got any links or instructions. Alternatively you could also buy a new module and install that, but then you need to take it to a mechanic with Tech 2 to get the new module married to your car. The battery and its tray must be removed, and the fuse box must be moved out of the way.
Step nine: remove ABS module from the car! I used a flat tip screwdriver and carefully unlocked the snap, then it slides down. I tried a deep well socket but it wasn't deep enough. Well, it actually is rather simple, but when looking for information on how to remove the darned module I couldn't find good instructions online. Save Up To 80% Off Dealer Prices! Sound simple, right? There are two electrical connectors on the module, a small one that connects from the bottom, and a large one that connects from the top.
Step seven: remove the battery tray by removing its four 10 mm bolts, and remove it from the car. Any more and you're bound to f something up.
It's a common problem, when the ABS module decides to quit, and you're left with a less safe car without ABS or traction control. This is your work area, the ABS module resides underneath the fuse box that lies behind the battery. Remove the module and send it to one of many rebuild services, then re-instal it.
ABS Sensor - Saab (4909966)
They are not captive, and come out going forward, which means that once they're loose they have a tendency of falling down onto the transmission. There are a number of companies that do the repair, including BBA Reman , which is the most famous one as most people recommend it. If you have the radiator overflow tank hose zip tied to it now is the time to cut that zip tie. Diagnostics: ABS module is faulty, module also controls TCS Traction Control System Fix: ABS module needs to be rebuilt or replaced Tools needed: - 13 mm socket or wrench - 10 mm socket or wrench - T20 Torx tool - one large zip lock bag - two small zip lock bags Tools recommended: - magnetic retriever - flashlight - zip tie cutter pliers, scissors, knife No promises are given explicit or implied.
What's New? Page 1 of 2 1 2 Last Jump to page: Results 1 to 10 of With winter set strongly, roads slippery and icy, all that kept me from fiery death were my snow tires. Step eight: remove those Torx screws, being careful not to drop them. Here is where the magnetic tool comes in handy, I had the tool on them before letting loose of the T20 tool, avoiding loosing them. All advice appreciated.
Step four: remove two nuts 10 mm holding down fuse box behind battery Step five: remove one nut 10 mm on the lower left bracket of fuse box left side as you look at it from the front of the car. Take a swig of your beverage. The large one has a sort of tray lock, you need to slide this tray to the left side, and at the same time it unlocks and disconnects from the module. Their site is well made and actually has a very good tutorial on removing the module.
Battery removed! Once the nuts holding the fuse box have been removed you can slightly move the fuse box out of the way, no need to remove it completely, but with it moved upward you have enough room to get to the ABS module. Hi, I need to replace the near side front ABS sensor can anybody tell me if this a big job or relatively easy. The fix? Now you will use the T20 Torx tool to remove the hardware holding the ABS module to the brake system.
Step six: here you have arrived at the ABS module itself. Picture shows vehicle with battery tray removed. There are six bolts, and they are hard to see. Once it's disconnected you just slide it to the side as on the picture. The ratcheting wrench came in handy here! The right side ones are the hardest since it's a tight spot with very little visibility. The bottom one has a sort of snap lock, you might be able to undo it by hand.
Figure it out on my own, and then make a tutorial for those that have the same problem in the future. What to do?